Home » Liquitex Acrylic Mediums » Liquitex Acrylic Gloss Medium & Varnish - Size: 8 oz.
Liquitex Acrylic Gloss Medium & Varnish - Size: 8 oz.
The workhorse of the Liquitex mediums range. Gloss Medium & Varnish in an
all-purpose medium that performs two functions. It can be used as a varnish
and/or a fluid gloss medium. It improves adhesion of paint film and increases
color depth, intensity, and gloss. It can also be used as a non-removable varnish
to protect the surface and establish an even gloss sheen.
- Soft Body.
- All purpose medium, formulated to be mixed into all Liquitex acrylic paints
- Mix into any acrylic paint to enhance the depth of color intensity,
increase transparency, gloss, ease flow of paint and add flexibility
and adhesion of
- Use as a non-removable varnish to protect painting and establish gloss
- Translucent when wet, transparent (clear) when dry.
- 100% acrylic polymer varnish. Water soluble when wet. Good chemical
and water resistance.
- Dry to a non-tacky, hard, flexible surface that is resistant
to retention of dirt.
- Resists discoloring (non-yellowing, non-fogging) due to humidity,
heat and ultraviolet light.
- Depending upon substrate, allows moisture to pass through
- Will not crack as surface expands and contracts during temperature
and humidity changes. Applicable for any surface (flexible
and inflexible) suitable for
acrylic paint and mediums, such as canvas, paper, wood,
- Not for use over oil paint.
APPLICATION AS A MEDIUM
As An Extender:
- Mix with Soft Body Concentrated Artist Color to extend volume and increase
transparency, while maintaining paint viscosity.
- Mix with Heavy Body Artist Color to extend volume and increase transparency,
while decreasing paint viscosity.
As A Fixative:
- Use as a fixative over artwork (acrylic paint, pastel, graphite, chalk)
to increase gloss or shine. Mix 1 part Gloss Medium & Varnish to 1
part distilled water. Apply with atomizer or airbrush.
As a Binder / Adhesive:
- Powdered pigments or aggregates may be mixed into Gloss Medium & Varnish,
however they must be compatible with acrylics.
- Collage material may be glued using Gloss Medium & Varnish as a liquid
As A Ground:
- Use as transparent ground for acrylic paint instead of gesso. Allows substrate
to be seen. To prevent Substrate Induced Discoloration, wash cotton or linen
canvas before use.
With Powdered Pigments:
- Use as a binder with powdered pigments to make an inexpensive student grade
Soft Body gloss paint.
APPLICATION AS A VARNISH
- Gloss Varnish for flexible surfaces is recommended as the best varnish
for acrylic paintings.
- Apply Gloss Medium and Varnish as a final permanent varnish over dry acrylic
- Varnish surface and environment must be clean, dry and dust free.
- Acrylic paintings must be completely dried and cured for: 48-72 hours
- Dilute Gloss Medium and Varnish up to 20% for better brushing and
- Application may be done by brush or spray. Generally a sprayed
application will be thinner, smoother and more even. Rolling or
is not recommended.
- Caution: Acrylic paints and mediums become increasingly brittle
in cold weather. Do not apply below 60 degrees.
Brush and Paint Pad Application
- Use a wide, soft hair brush or paint pad (vacuum pad prior to use to
remove lint). Size of area to be varnished will determine the size of the
The smaller the surface area, the narrower the brush. Generally, a 1-4" flat
brush is used.
- Apply varnish in 1-3 thin coats, rather than 1 thick coat. A thick coat
will take longer to dry, may dry cloudy, may drip or sag during application
and has a greater chance of showing brush strokes when dry.
- Horizontal surface application is best with less chance of varnish running.
After varnishing, the surface should be shielded with a protective "tent".
This will prevent any dust or airborne particles from settling into varnish
as it dries
- Apply varnish in slightly overlapping pattern that covers entire artwork.
Apply in horizontal and vertical brush strokes, so that entire area is evenly
- Do not rework areas you might miss, as the brush could pick up partially
dried varnish and cause clouding. If areas are missed, wait until the varnish
is dry and apply another coat.
- When applying Liquitex Permanent Matte Varnish or Satin Permanent Varnish,
apply no more than 1-2 thin coats. A thick application may result in cloudiness
when dry. If more than 2 coats are desired, first varnish with Gloss Medium & Varnish
until desired thickness is achieved, then final varnish with matte or satin
- Refer to Techniques and search on "Airbrushing" for more detailed
- Most even application method.
- Use for textured surfaces (thick impasto, thick textures), where brush
application may result in foaming and fragile surfaces (watercolor,
pastel, gouache), where brush application may disrupt drawing or painted
- Select air pressure (PSI) depending on air gun used and viscosity of varnish.
Greater PSI permits thicker varnish to be sprayed, but may affect fragile
- 2-3 light even coats are better than 1 thick coat.
- Spray a continuous film by moving the spray gun in a smooth motion from
one side of the painting to the other. First coat horizontal, second coat,
third coat horizontal, etc.
- During spray application, maintain same distance across the surface of
the artwork. Move your body as well as your arm to avoid "arching" motion
and uneven application.
- Thinning increases penetration and can make it easier to apply varnish.
- Over thinning may result in weak varnish film, poor adhesion, running and
soaking into substrate.
- You may thin Gloss Medium & Varnish with water up to 25% for better
flow, leveling and for spray applications.
- Thin with small amount of Flow-AidTM/water to reduce brush marks or spray
apply. Refer to Liquitex Paint Additives: Flow-Aid Flow Enhancer.
- Not removable. Do not attempt to remove these varnishes with harsh solvents.